Condor Tactical Gear Mesh Hydration Vest Review

Law enforcement professionals use equipment vests, carrying armor or not, for various purposes. In this article, the author reports on his experience wear-testing the Condor Tactical Gear Mesh Hydration Vest.


About a year ago my youngest son joined an organization and became (almost immediately) a part of their search & rescue team. He needed a vest. He inherited mine and we reconfigured it for his intended use. I needed a replacement and borrowed an armored vest from a friend, configured it for my survival/emergency preparedness use and drove on. However, I knew that I eventually needed to procure a new vest and return the armored one. So, a couple months ago, thanks to WTG Tactical I became the proud owner of a Condor Mesh Hydration Vest. I didn't need the vest to carry armor; I just needed one that I could MOLLE mount gear pouches and a holster onto. This vest has worked perfectly.

My old vest, the one my son inherited, had both a zippered AND buckled front opening. You put it on like a jacket rather than pulling it over your head like most body armor. I always felt that the zipper and buckles were a bit redundant but redundancy is often good so I dismissed any questions or concerns from my mind. Then I saw folks who either cut off the buckles and only used the zipper, or folks who only buckled it and acted like the zipper didn't exist. For them, convenience took place over redundant security where it came to holding the vest closed/on. The Condor Mesh Hydration Vest (MHV) has only buckles; three of them, and they work just fine in holding the vest on. To reduce stress on the buckles and help them last even longer (although they'll probably work just fine long after I'm dead and gone), it's important you adjust your vest to fit properly.

The Condor MHV has six size adjustment straps: three on each side in the back. To adjust fit properly, put the vest on and buckle it closed; then pull the straps in turn until the vest fits snuggly but not uncomfortably. DO NOT cut off any excess strap, but instead roll them up if you don't want them dangling. Velcro wrap straps are provided with each one so you can secure them once their rolled up. Why don't we cut them? Think about the different seasons and what clothing (or armor) you might need to don this vest over. Make sure you have room to adjust the vest by leaving the straps full length.

The vest has padded and adjustable shoulder straps as well as a padded back with an emergency drag handle (which I most often use as a carry handle if I have to move the vest but aren't wearing it) attached securely at the top center of the back. The padded shoulders help the vest be more comfortable to wear even when it's loaded with gear and that weight is pulling into your shoulders. The fact that the shoulder straps are adjustable means you have some leeway in adjusting the bottom of the vest to sit where you'd like it to. The padded back provides a little stiffness, generally allowing some air flow between your back and the vest, helping to keep you cool and allowing sweat to evaporate. There is also a hydration pocket on the back but that's OUTSIDE the padding. Not only does this help keep the water cooler (because ambient temperature is usually cooler than body temperature), but it also let's the padding be directly against your back if you lean on anything to rest or get a stable position.

Around the waistline of the vest are six snapping belt loops that allow you to attach a gunbelt to the vest. In doing so, you create a single system that allows you to pull on and buckle the vest, buckle the belt, buckle leg straps and be on the move. That said, I'm not a fan of that arrangement so I consider the belt straps inconvenient and cut them off of my vest.

The vest is covered with MOLLE webbing, both front and rear, including on the outside of the hydration pocket (hydration bladder/tube not included) and farther up on both sides than most other vests I've seen. On the top four rows of MOLLE webbing in the front, there is velcro face so you can affix patches. For instance, I have a blood type patch affixed on the right side of mine, or you could put a name tape on there if you needed/wanted to. On the back, on the flap closure for the hydration pocket and the top row of MOLLE, there is more velcro face for patch attachment.

This content continues onto the next page...
  • Enhance your experience.

    Thank you for your regular readership of and visits to Officer.com. To continue viewing content on this site, please take a few moments to fill out the form below and register on this website.

    Registration is required to help ensure your access to featured content, and to maintain control of access to content that may be sensitive in nature to law enforcement.